-
E-mail
2623777888@qq.com
-
Phone
18136266333
-
Address
Baoying County Economic Development Zone, Jiangsu Province
Yangzhou Jinguan Electric Co., Ltd
2623777888@qq.com
18136266333
Baoying County Economic Development Zone, Jiangsu Province

Brief introduction
The GZ03-S05 fully automatic cable hot air dryer heats the cold air and enters the cable box. Through the cable box, it then enters the cable to be dried, expelling the water and moisture inside the cable and achieving the same insulation level as before (above 2500M Ω). It is safe to use, easy to move, energy-saving, reliable in operation, and has high work efficiency. It is an ideal equipment for drying cables in coal mines, iron mines, and well construction units.
detailed description
1、 Structure Introduction
GZ03-S05 Fully Automatic Cable Hot Air Drying MachineUsed for drying rubber sheathed cables, it has * level and is mainly composed of a frame, electrical instruments, air compressor, sealer, pressure resistant tube, cable box, infrared heater and other systems. The working principle is that the air is compressed by an air compressor into a sealing device for filtration, and pure air is pressed into an oven. The cold air is heated and enters a cable box, which then enters the cable to be dried. The water and moisture inside the cable are expelled completely, so that the cable can reach its original insulation level (above 2500M Ω). It is safe to use, easy to move, labor-saving, energy-saving, reliable in operation, and has high work efficiency. It is an ideal equipment for drying cables in coal mines, iron mines, and well construction units.
2、 Operating proceduresGZ03-S05 Fully Automatic Cable Hot Air Drying Machine
1. After connecting the power supply during work, turn on the main power and adjust the temperature controller to the temperature required for heating the cable.
2. After heating up, turn on the air filter switch to allow air pressure to pass through the electric heating box, and turn on the wire switch to allow dry hot air to be pressed into the cable.
3、 Precautions during drying
1. When drying with hot air, attention should be paid to the temperature values of electromagnetic preheating and changes in coil current at all times. The index of the thermometer should not exceed 60 degrees, nor should it be lower than 35 degrees, and should be kept within the above range.
2. After the cable has been dried for a period of time, a megohmmeter can be used to measure its insulation resistance at the exposed ends inside and outside the cable. If the drying effect is good and the insulation resistance can reach 150-250 megohms, the drying can be stopped. If the drying effect is slow after several cycles, the cable can be turned around and dried again until it meets the requirements.
3. During the drying interval, the drain valve at the bottom of the filter should be continuously opened to discharge air, in order to improve the quality of the compressed air.
4. During normal drying, if the cable sheath is blown into bulges by compressed air or a large amount of talc powder flows out of the core, the air pressure should be reduced. At this time, attention should also be paid to observing the escape of compressed air between the cable outer leakage end sheath and the core. If the escape condition is unfavorable compared to the cable, a wooden rod can be used to lightly tap the cable sheath to facilitate smooth passage of compressed air.
5. During the drying process, there will be compressed air escaping from each opening (or hole) of the cable sheath. At this time, it should be marked for easy heat repair after drying.
4、 Basic parameters
1. Working voltage: 220V
2. Heating power: 4-8kW
3. Heating temperature: adjustable from 0-300 ℃
4. Dry cable length: ≤ 600m
5. Maximum wind pressure: 0.8MPa adjustable
6. Dimensions: 1600 × 600 × 1100mm
7. Weight: 265KG
After sales service system of Jinguan Electric:
Our company has a professional after-sales service team, and the after-sales service department is led by the vice president in charge of sales.
2. The after-sales service department currently has dedicated personnel who can ensure timely maintenance of the company's products.
Our goal for after-sales service is to promptly resolve on-site equipment malfunctions, respond quickly, and provide excellent service!