Liang Jin vortex high-pressure blower

The impeller of Liang Jin's vortex high-pressure blower is composed of several blades, similar to the impeller of a large gas turbine. The air in the middle of the impeller blades is subjected to centrifugal force and moves towards the edge of the impeller, where it enters the annular cavity of the pump body and circulates again in the same way from the starting point of the blades. The circulating airflow generated by the rotation of the impeller leaves the air pump with * energy for use. Fan, small size, light weight, low noise, no water or oil in the air source sent out.

Vortex high-pressure blower specifications three-phase voltage power: 0.2 KW、0.25KW、0.37KW、0.4KW、0.55KW、0.75KW、0.85KW、1.1KW、1.3KW、1.5KW、1.6KW、2.2KW、3KW、4KW、5.5KW、7.5KW、8.5KW、11KW、12.5KW、15KW、18.5KW、20KW、25KW；
Single phase voltage power: 0.2KW 0.4KW 0.55KW 0.75KW 0.85KW 1.1KW 1.3KW 2.2KW;
Wind pressure: 50mbar-1010mbar;
Airflow: 40m3/h-3000m3/h (for the convenience of selecting different specifications, both single-stage and two-stage models are available in stock);
Frequency: 50HZ/60HZ Voltage: 110V-615V (applicable to all countries). If special voltage is required, it can be customized according to requirements;
Pressure relief valve: RV-01 RV-02 (for use with);
Filter: MF08 MF10 MF12 MF16 MF20 MF32;
Muffler: Interface 1.25 inches 1.5 inches 2 inches 2.5 inches 4 inches.

The vortex high-pressure blower has functions: 1. It has dual functions of blowing and suction, and can be used for both suction and blowing; 2. Running with little or no oil, the output air is clean; 3. Exhaust and supply fans are divided into:; Pneumatic conveying and pipeline conveying; 4. Can be modified to include six major features: thermal insulation, waterproofing, explosion-proof, anti-corrosion, coupling transmission, and belt transmission; 5. The shell is die cast as a whole and uses shockproof mounting feet, so its requirements for the installation foundation are also very low. It can even operate normally without fixing the feet, which is very convenient and saves installation costs and installation cycles; 6. The fan blades that generate centrifugal force are made of double-sided forward leaning multi blade, molded in one go, with high-quality dynamic balance by computer, extremely low vibration, stable wind force, low noise, and can withstand certain frictional impact force, with a long service life; 7. The drainage side panel has a built-in side suction port, which, when combined with the fan blades, can generate a large negative pressure suction force, making the self-priming feeding more stable.

Precautions for installation of vortex high-pressure blower: 1. Installation location of high-pressure blower: It must be installed indoors in a place that is not affected by wind and rain; 2. Environmental temperature: below 40 ℃; 3. Relative humidity: below 80%; 4. Air quality: If the air contains corrosive or flammable gases such as acids and alkalis, it should not be transported by high-pressure blowers to avoid danger; 5. Dust protection: Avoid using in places with large amounts of dust, powder, or fibers. If it is necessary to use in such places, please install a filter and regularly clean the dust attached to the filter screen and inside the high-pressure blower; 6. Ventilation and heat dissipation: Please choose to use it in a well ventilated place and not in a sealed room or box; 7. Placement space: For the convenience of column maintenance or repair, please avoid installing in overly narrow locations; 8. Avoid vibration: Please install in a vibration free location; If the vibration in the venue is unavoidable, anti vibration measures must be installed to prevent the high-pressure blower from being damaged by external vibrations.