TANWELL oil mixed with water

TANWELL oil mixed with waterWM1-L100-MS-230VAC, DTA3300 displacement monitor is a four channel monitor. It can accept signals output by non-contact sensors and use these signals to drive alarms. Configure the 3500/40 using the 3500 framework configuration software. The change in fluid flow rate is reflected by measuring the difference in resistance between these two thermistors. Wear resistant thermal flow sensors can be used for monitoring the flow rate of liquid or gas media. High cost-effectiveness.

TANWELL oil mixed with waterWM1-L100-MS-230VAC, DTA3300 displacement monitor is a four channel monitor. It can accept signals output by non-contact sensors and use these signals to drive alarms. Configure the 3500/40 using the 3500 framework configuration software. The change in fluid flow rate is reflected by measuring the difference in resistance between these two thermistors. Wear resistant thermal flow sensors can be used for monitoring the flow rate of liquid or gas media. High cost-effectiveness.

Flow monitoring is a program that requires reliable and repeatable monitoring of limit values and flow states. Flow sensors can detect key deviations in the flow velocity of liquid and gas media. Typical applications include monitoring cooling circuits during welding (such as preventing pump idling) and monitoring flow in ducts and air conditioning equipment. Due to the use of thermal principles, sensors can also monitor the temperature of the medium.

Compact plug-in flow sensor

Liquid monitoring flow sensor

Thermal functional principle

Display traffic status through LED

5-wire DC, 19.2... 28.8 VDC

Functional Principle

Plug in flow sensors are based on the thermal principle. The measuring probe heats up by comparing with the temperature of the fluid medium, and when the fluid passes through the probe, it takes away some of the heat. The change in fluid flow rate is reflected by measuring the difference in resistance between these two thermistors. Turck wear-resistant thermal flow sensors can be used for flow rate monitoring of liquid or gas media.

Switch status indication

Convertible contacts, relay output

A: I/O module type 01 displacement/velocity acceleration I/O module with internal terminals

0 2 Displacement/Velocity Acceleration I/O Module with External Terminals

Triple Redundancy (TMR) I/O Module with External Terminals

0 4 I/O module with internal safety barrier (4 x displacement/acceleration channels) and internal terminals

0 5 with internal safety barrier (2 x displacement/acceleration 2 x speedometer channel)

0 6 I/O module with internal safety barrier (4 x speedometer channels) and internal terminals

125808-02 Displacement/Velocity Acceleration External Terminal Block (European style connector)

128015-02 Displacement/Velocity Acceleration External Terminal Block (Terminal with Connector)

132242-01 Displacement/Velocity Acceleration Bus Type Triple Redundant External Terminal Block

132234-01 Displacement/Velocity Acceleration Bus Type Triple Redundant External Terminal Block

128702-01 Recorder External Terminal Block (European style connector)

128710-01 Recorder External Terminal Block (Terminal with connector)

140993-01 shaft vibration external terminal block (European style connector)

141001-01 Axis Vibration External Terminal Block

6 LED indicator light chains green/yellow/red

The light indicates the flow rate status

6 LED indicator light chains

Display: Flow rate below set value

LED indicator light red

Display: Flow rate is equal to the set value

LED indicator light yellow

Display: Flow rate higher than the set value

4-channel LED indicator light green

Installation method

Plug in sensor

scope of work

1…150cm/s

scope of work

3…300cm/s

Switch characteristics

typ. 8 s (2…15 s)

open time

typ. 2 s (1…15 s)

Close time

typ. 2 s (1…15 s)

Temperature gradient, response time

Big 12 seconds

temperature gradient

ð 250 K/min

medium temperature

-20…80 °C

Working Voltage

195…264VAC

Current loss

ð 30 mA

output performance

Relay output, complementary contacts

Rated working current

4 A

short circuit protection

No

AC switch voltage

250 VAC

DC switch voltage

60 VDC

Large AC switch capacity

1000 VA

Large DC switch capacity

60 W

housing material

Plastic, PBT

Probe material

Stainless steel, AISI 316Ti

High torque

100 Nm

connect

cable

Cable length

2 m

Cable cross-section

5 x 0.5mm

2

pressure rating

100 bar

process connection

G ½″