FT-105Apparent density tester
FT-105Apparent density testerAfter the upgrade, the following features have been added:In addition to the positioning angle, this product is equipped with a level device for adjusting balance to reduce the influence of external environment on measurement results; The funnel and measuring cup have positioning devices to ensure that the centers of the funnel and measuring cup are in a straight line; And install a height measuring ruler on the bracket, which is beneficial for adjusting the funnel height measurement
FT-105Apparent density testerThis instrument is mainly used for determining the apparent density of loose plastic material left in a specified funnel, and for determining the apparent density of polyvinyl chloride resin
FT-105Apparent density testerIt is an ideal testing instrument for quality inspection of raw materials entering the chemical industry and plastic profile factories. The product meets the requirements of standards such as GB/T3402 and GB/T1636.
FT-105Apparent density testerTechnical parameters:
Choose one： Type A funnel requirements
Main components: base, support frame, funnel, insert plate, receiving cylinder
Receiving cylinder volume: 100ml ± 0.5ml
Diameter 45mm
Sampling quantity: 110ml-120ml
The funnel angle is 40 degrees and the aperture is 33mm
Can meet the requirements of K-6721 (1966)Choose two
： B-type funnel requirements
Funnel angle: 20 degrees; The diameter of the funnel is 91mm; Inner diameter of discharge outlet: 10mm, made of stainless steel material, equipped with outlet control valve and baffle; The height of the funnel and measuring cup can be adjusted, and the diameter of the measuring cup is 45mm; Volume: 100ml ± 0.5ml, made of stainless steel material
Sampling quantity: 110ml-120ml
This instrument is mainly used for measuring the apparent density of loose plastic materials flowing out of specified funnels, and is an ideal testing instrument for the quality inspection of raw materials entering the chemical industry and plastic profile factories. The product complies with GB/T3402 GB/T1636
The requirements of GB/T20022-2005 GB/T13173-2008 and 1636-79 standards.
Apparent density tester
This method is suitable for measuring the apparent density of powder molded plastics, which is the mass per unit volume, providing parameters for the packaging of molded plastics, the design of mold cavities, and extrusion screws. Complies with the standards of GB/T 3402 and GB 1636.
Apparent density tester
1. Sample: Extract samples according to product standards.
2. Experimental instruments:(1) Balance: Sensitivity of 0.1 grams
（2）
Surface Appearance Tester(3) Measuring cylinder cup: 100 milliliters
Note:
Please keep in touch with us for specific parameters and related supporting products,
Configuration: Steel ruler; Brush, base, support frame, funnel, insert plate, receiving cylinder, instruction manual, certificate of conformity, warranty card, etc.
Ruike Instrument Company can also provide solutions related to powder testing
1. Operation method
a、 Open the packaging box, take out the measuring instrument, and count the components according to the packing list.
b、 Place the measuring instrument on a stable workbench.
c、 Insert a plug into the lower outlet of the stainless steel funnel and place a feeder under the funnel, coaxial with the funnel.
d、 Measure 110ML-120mL of the sample using a measuring cylinder and slowly place it into the funnel.
e、 Quickly remove the plug and allow all samples to naturally leak down (the feeder filled with samples must not be subjected to vibration).f、 Scrape off the excess sample from the feeder mouth with a ruler, and then weigh it on a drug balance until it reaches 0.2g (the measured sample cannot be repeated).Powder/Particle analysis instrument; Powder/Particle detection laboratory; Powder/Rental of particle instruments; Powder
/Particle analysis solutionNote:
There are also related supporting products,Please keep in touch with us
You may be interested in the following products：FT-100
Vibration density tester;
FT-101Scott Capacity Meter Loose Density TesterFT-102Hall current meter/Loose density tester-
Stainless steel material;FL4-1Hall current meter/Powder flowability tester
-Yellow BrassFT-103
Bulk density tester;
FT-103AActivated clay bulk density measuring device;
FT-103BDust resting angle measuring instrument;FT-104
Aluminum oxide loose density tester;
FT-104AAngle of repose tester;FT-104B
Angle of repose tester;
FT-104CAluminum fluoride flowability tester;
FT-105Apparent density testerFT-105A
Active agent apparent density determination device;
FT-105BMeasurement device for apparent density of slurry;FT-105C ASTM
Plastic apparent density meter;FT-106Abrasive Bulk Density Tester (formerly known as
DMP-II）FT-106A
Micro powder bulk density tester;
FT-106BSuperhard material bulk density tester
FZS4-4Vibrant density tester;
FT-102AVibration Funnel Loose Density Tester
FZ4-3Type vibrating funnel loose density tester;
FS4-2Scott Pine Density Tester
DMP-IIOrdinary abrasive bulk density tester;FT-107Fertilizer bulk density(loose
)Measuring instrument. ROOKO/
